DIY Microscopy Instruction (French)

From Hackteria Wiki
Revision as of 10:24, 28 December 2015 by Remy (talk | contribs) (1. Conversion of the webcam Part A: Small enlargement)
Jump to: navigation, search

Instructions to be translated

!! WORK IN PROGRESS !!

[[File:hackteria-mikroskop-2012-137.JPG|right|400px|thumb|The Chapter about the DIY microscope can be downloaded here and available now with Chinese translation included!

Would be great to have this also in other languages, below is the english original to get you started.

Translations

DIY Mikroskop Anleitung (Deutsch)

DIY Microscopy Instruction (Chinese)

DIY Microscopy Instruction (Spanish)

DIY Microscopy Instruction (Bahasa Indonesia)

DIY Microscopy Instruction (French)

DIY Microscopy Instruction (Japanese)

0. Introduction et matériel nécessaire

Le but est de construire un DIY MICROSCOPE, un microscope à partir d’une webcam ordinaire. La conversion d'une webcam en microscope est rapide et facile à réaliser manuellement.

La partie électronique de la webcam reste inchangée, seule la position de la lentille est modifiée! Une petite plateforme permet de la fixer et de faire le focus de manière précise sur les petits objets à observer. Les objets sont éclairés avec une diode électroluminescente (LED).

Le DIY MICROSCOPE consiste en trois éléments, assemblés dans cet ordre :

  • une webcam converti
  • une plateforme stable pour l’observation
  • un éclairage avec une diode électroluminescente (LED)

Liste des pièces / matériel

DIY-Microscope Instructions Materials.png

Base

  • Une webcam
  • Carton (épais) / bois, 20 x 30 cm
  • Panneau de mousse, 20 x 30 cm
  • Une longue vis M4, approx. 15 cm de long, avec écrous M4
  • Scotch d’électricien (scotch isolant)
  • De la Patafix
  • Bâton de colle chaude
  • Élastiques

Outils

  • Cutter / couteau bien aiguisé
  • Tournevis
  • Pistolet à colle chaude
  • Fer à souder (facultatif)

En option, source lumineuse externe (LED)

  • Un interrupteur
  • Une LED blanche
  • Une pile (9 volts)
  • Une clip pour pile 9 volts
  • Une résistance (1 k Ω )
  • Un potentiomètre (20 k Ω )
  • 30 cm de fil électrique isolé
  • Du fil de fer fin

Microscopie et équipement de collecte microscopique

  • Quelques gobelets plastiques transparents
  • Lames de verre
  • Boites de pétri (plastiques ou verres)
  • Pipettes de prélèvement
  • Stylo waterproof
  • Petite cuillère d’acier chromé
  • Pince à épiller
  • Contenant plastique avec couvercle

1. Conversion de la webcam Partie A: Petit élargissement

Step 1 get stuff.jpg

  • Une sélection de webcams standards. Les plus adaptées sont les modèles disposant d’un ajustement manuel du focus en tournant la lentille. La seule solution est de tester!
  • Avant de commencer à modifier la webcam, il est nécessaire de la tester. Pour cela, il suffit simplement de la connecter à un ordinateur et, éventuellement, d’installer des drivers supplémentaires (ils se trouvent le plus souvent sur le site de la marque, ou via un moteur de recherche avec le modèle de la webcam). Les webcams fonctionnement sous Windows, Linux et OSX. Sous Linux, il peut être un peu plus difficile de faire fonctionner certains modèles...

Step 2 screw lens outwards.jpg

  • Dans cette configuration, avant modification, la webcam peut être utilisée pour observer des objets de près. Il faut seulement dévisser la lentille et rapprocher l’objet. Une lampe de poche améliore les conditions d'éclairage.
  • Pointer la webcam en direction de petit objets permet de voir des choses étonnantes: Même sans modifications , on commence à voir des choses cachées à l'oeil nu.

1. Conversion of the webcam Part B: Maximal enlargement

Step 3 invert lens.jpg

  • Now we begin dismantling the webcam. The screws are removed. Partly such screws are hidden beneath labels or rubber caps. With a solid tool – in this case the screwdriver of a Swiss Army knife – the webcam ’s cover is removed.
  • The appliance ’s interior can now be seen: it consists of optics and an electronic switch. We can do without the light-emitting diodes (LEDs). We shall later construct our own light.
  • The optics is partially glued on. By careful twisting we can detach it from the electronics. The optics’ outer ring (at the right of the picture) will no longer be used later. It only serves as decoration.
  • With the use of a strong side cutter we cut through the plastic casing. Now the electronics including all wires and the USB cable can be removed from the casing.
  • The webcam’s interior: on the left side of the picture we can see the internal microphone, which, however, is not needed for our project.
  • Now we place the optics upside down on the fitting. It can no longer be screwed on and must therefore be firmly secured. The optics is attached with a piece of duct tape.
  • To test the equipment we connect the modified webcam with the computer and point the lens towards the screen. Now the individual

RGB pixels on screen become visible.

2. Construction of the platform

Step 4 make stage.jpg

  • Using small lumps of Blu-Tack adhesive, the webcam is attached to a solid pasteboard of about 15 x 15 cm.
  • The platform’s side wall consisting of scale model cardboard. With a pencil we draw the height of the lens on it and cut off the cardboard along that line. We use hot glue for pasting.
  • Using a carpet cutter, we cut a rectangular opening into another piece of scale model cardboard. This piece too is attached with hot glue.

Step 5 adjustable focus.jpg

  • The adjustable screw requires a hole. We attach the screw nut right at the top with a small drop of hot glue. Then we insert the adjustable screw. It must reach down to the lower platform.
  • Rubber bands provide more stability to the platform. With the screw the scale model board can now be moved up and down by a few millimeters.

3. The light source

Step 6 add ligthing.jpg

  • Our microscope also has a light source in the form of a light-emitting diode (LED). The lighting can be easily produced by oneself.
  • In this easy way, the wires can be twisted together. But it is safer if they are solded on.
  • The centimeters long feed of our light source is wrapped with garden wire. The wire thus becomes pliable and later can be attached in any position.
  • The light source, potentiometer and battery are attached to our construction with hot glue. Our DIY MICROSCOPE is ready for use.

3.B Hacking the LEDs from the Webcam (to be documented)

  • Coming soon

4. Using the Microscope and Hunting for Microorganisms

Step 7 go hunting.jpg

  • The USB cable of the converted webcam is connected to the computer. Now we can begin with our examinations.
  • The study objects are placed on a glass slide and can be shifted by hand. The microscope’s focus is regulated by the adjustable screw.
  • As with a professional microscope, with our DIY tool we are able to take electronic photos and even films. Photos and films are digitally available, can be further processed and of course be easily published on the Internet.